An Embedded Microcontroller or DSP system is made of Chips, Circuits and Firmware. The digital voltage levels, speed, bus width, fan out, power consumption are some factors that a designer has to keep in mind. As portable and wireless gadgets are becoming more popular, RF, Ethernet and Energy Efficient Design aspects should be studied. Power electronics and Analog Circuits knowledge is used around the system, all this is integrated to make an instrument, equipment or gadget.
These are pages about circuits and products that use Microcontrollers. These are digital chips that derive their intelligence from the firmware program that a user loads into it. Tiny Logic and Math elements simulate Digital Logic according to the programmed instruction to obtain a desired result. Having an equivalent math or logic circuit for the same result would take enormous space, cost and effort. I cover this subject in the blog below.
Hyper Embedded - Microcontroller, FPGA, ASIC.
- 80C51 ports can sink more current but source very less, hence use a 10k pull up at all the ports or outputs.
- Firmware must be developed in increments, tested in increments, backed up in increments, must be modular (include) reuse.
- Tristate output, High Impedance and Floating all mean the same when it comes to IC Inputs-Outputs. It means the pin is insulated from rest of circuit in the IC. That means it will not influence the node or bus it is connected to. A DMM terminals are floating means that the hand held plastic DMM has no electrical conductive link to earth or ground.
- You can use hyper terminal to upload code to single board computers 80C51 like in BINARY or ASCII. Hyper Terminal, .
- ASICs are for large volume production, or for products which have a long product life cycle.
- Low volume production use FPGA or CPLD, or even flash based microcontrollers, so that all your inventory can be reused and recycled.
- Cell phones or a LAN card ASIC is ideal as volumes are good in cell phones and for LAN cards the technology is matured. For either FPGA or ASIC's you get IP Modules or Code Libraries for many functions and applications.
- Whatever the method keep design flexible and modular for reuse and to save cost. remember the hardware is difficult to alter, software can be altered even at customer site, flash has made this possible
- In the future chips may be both analog and digital programmable with flash.
- Some FPGA, CPLD, ASIC links, WinCUPL, Design and Reuse, fpga4fun.
- Unused CMOS inputs should have a pull up or pull down resistor, it should not float, or it oscillates.
- Have a decoupling capacitor 104 that is 0.1uF or 100nF across the supply of every IC very near the IC supply pins.
- A watchdog timer should be used in every microcomputer circuit like 8051 so that the system resets on hanging.
- The reset on a microcomputer should be applied till the supply to it is stabilized, this will enable a clean start.
- Analog ground (opamps), digital ground (CMOS) and power ground (relays and LED) should be separate, (linked at root)
- Pull up or pull down resistors in TTL can be 10K and in CMOS 100K and in battery operated systems 1M.
- CMOS gates and Opamps have a output drive capability of ~ 10-20mA, so when you drive a load say an LED use a series resistor to limit the current to 5mA to 10mA.
- When the number of digital chips you use in a project goes above 20 or 30 then it is better to use PLD or CPLD types from Altera, Xilinx or Lattice etc.
- Try to use same family ICs in a circuit, like only LS or only HCT, if you mix up then you have to do a design review.
- In a industrial environment many motors, DC drives and AC drives will be running, this will produce EMI, RFI, kickback spikes which cause microcontroller based equipment to hang. Use a watchdog timer for uC.
- More EMI immunity by using opto couplers for all input and outputs, 4-20mA current signals for input and output and an isolated wide range SMPS.
At Beyond Logic and Embedded Processor Control you will find interesting information on interfacing. Real World variables are analog values, like the temperature of the Human Body. There may be Yes-No or digital events too, like the Water Level of a Tank or Door Close-Open. The former is measured by a Thermocouple and the Latter with a Proximity Switch. These values from the sensors have to be Quickly converted to a digital form and fed to the the uC by an interrupt or cyclic polling of ports. The "How Quickly" determines How "Real Time" you system response is. An analog value in instrumentation has to be at least 12 bit wide resolution, which is like 3-1/2, and the The ICL7135 4-1/2 gives +/- 20,000 counts at full scale, nearly 14bit wide data. This can be interfaced both in serial and parallel data links. The serial method is used when optical isolation is required from the sensor to control circuits. If the sensor is measuring the temperature of a Transformer, an optical isolation is absolutely required.
Microprocessors and Microcontrollers
Analog devices like transistors and diodes lead to opamps and analog computing. This takes more parts but with fast devices can be real time. Then came Logic and Digital Circuits, here also big systems will take too many parts. A very Old hp Logic Analyzer instrument, could be HP1600A, had more than five large PCBs, Toggle Switches and numerous 74Fxx TTL Chips. I tried to revive it, it could not be fully restored. Then came the solution the Microprocessor. Here the entire system goes into the firmware and a Hardware Tool Set in the Microprocessor made up of Logic and Math is sequentially used to perform the same operation that would require innumerable Gates in a plain hardware digital circuit. But as it performs the operations one after another, it takes time and is defined by the CPU Clock Speed. When the External RAM and EPROM and other peripheral devices moved into the main package, MicroController were born. When more external devices merged with the MicroController. It formed a nearly complete computer, this is known as the SOC.